DuctlessAire Outdoor Wall Bracket - Mini Split Mounting Bracket - Ductless Air Conditioner Wall Mount - Mini Split

This mini split mounting bracket is sturdy and well-made. Installation was straightforward, and it holds the unit securely without any wobbling. The metal feels durable and weather-resistant, giving confidence that it will last. Overall, a reliable bracket that does its job and makes mounting a mini split much easier. Read more

Instructions say the top horizontal arm holds no weight and weight must be placed on the fasteners of the 2 vertical arms. So Its nice to hit 2 studs. Unfortunately I did not, and hit 1 stud..Then Drilled a 1/2 inch hole into the stud. Trying to install a toggle bolt...Luckily, after careful deliberation I filled the 1/2 inch hole with exterior wood glue and a piece of half inch dowel, and was able to capture, at least, 1 vertical arm with the included lag bolt fasteners on a stud. The other arm got the toggle bolts. Unfortunately I could not locate a stud for 1 vertical arm. After doing some heavy engineering maths on 3 or 4 different types of fasteners I used, I came up with the number of how much weight this could hold, based on the fasteners, and it was well over 4x the 60 lbs. I weighed my condenser at. Using the engineering maths weights I felt comfortable doing a few dips off of the mounting bracket to check my work. I do believe the top horizontal arm does add some structural support and the manual is saying dont depend on it, just forget the top arm exists when making your engineering weight calculations with fasteners and what youre mounting into. Now that the mount is mounted with fasteners. The quality of the mount is there. Its fully capable of securing the 55 lbs of load. The rubber feet dampeners do help with noise reduction and I consider what is included robust for the quality of the dampener. Most importantly is the arms length. Its a little longer and gets my unit farther away from a flush mount with the wall. This is important to increase the efficiency of the unit as it tries to draw in air from behind it. You want these long arms to give more room behind the unit. Read more

These brackets worked out perfectly for our mini split installation. The unit was professionally installed, and even the installers commented on the solid quality of the brackets and how well they were built to hold the weight. The picture shows our larger 24,000 BTU C&H unit, and the brackets are supporting it with no problem at all. They’ve proven sturdy and reliable, giving us confidence in the setup, and I will update this review if anything changes! Read more

This wall mount is great,I bought a 2nd one I was so impressed with the first. What I believe sets this apart from the majority of the other mounts, is the bracket that you mount to slide both of the legs into allows you to easily line up and adjust the width of the compressor mounts vs. the other mounts which require you to be pretty much dead on when you mount them width wise. The same is for the depth of the mounting feet which give you plenty of adjustment for pretty much any mini split mounting footprint. The mount is well built and solid and I don't foresee any issues with it. I used them both, one for an 18k compressor and also a 12k compressor. There was still plenty of adjustments for the mounting pads that I'm sure would accommodate up to the largest mini split compressors. The anti-vibration pads work great and were easy to install and line up. I would highly recommend this mount as I don't think it can be beat both for the price and quality and ease of mounting. 7 stars Read more

It's a sturdy mount, that's not hard to install. Seems to hold my 18K BTU MRCool condenser fine attached to wooden siding house. I didn't actually mount it to the studs, because I can't locate them from outside. But I think siding plus 3/4" plywood is sufficient. There are multiple reasons for which I took one star off. First of all, installation manual is lacking, and plain wrong in few cases. For example, when you attach "brace bar" you CAN'T slide brackets on it, because mounting screws will block it's path! So mount just one end, slide brackets, and mound second end. Another issue I had is because of the size of my condenser (it's narrow) I could only clear one of the top holes, so one arm is attached with 3 screws, and another one with just 2. I could've drilled new hole in metal, but I don't believe it's necessary as my condenser is not that heavy. They say in the manual that horizontal bar doesn't support any weight, but it actually does. It probably won't work on it's own, but it does provides extra support, a lot of it. Biggest issue (as other reviewers commented) is that when braced against wall, bottom of brackets are nowhere near level. I saw one reviewer used washers at the rubber feet, I think it's a great idea. It's probably the only way to level condenser unit. Finally, rubber legs have extremely long threaded rods on them. There's absolutely need for this, and it makes using socket wrench to tighten them a real pain in you know what. Overall it's a good bracket, but don't expect your condenser to be stiff, it will shake a little... Read more

Love this product I’ve used it several times in the past it works really well easy to just adjust and if you ever have to replace the unit, you can adjust it again Read more

The instructions are very clear it all went together easily. I used the provided wall fasteners, but they will need to be painted- they will rust. Read more