Sof Sole 3 7 Ounce Goo Repair Adhesive for Fixing Worn Shoes or Boots Clear 3 7-Ounce Tube

This review is for: Shoe Goo Repair Adhesive for Fixing Worn Shoes or Boots, Clear, 3.7-Ounce Tube ============================================================================== I had several pairs of shoes that needed repair, including fabric separating from the insole, holes in the leather uppers, and three pair where the soles were either completely separated or almost so. There were slippers, tennis shoes and a pair of Teva sandals. I honestly didn't expect this product to work very well because it just seemed unrealistic to use store-bought glue to properly re-attach soles, with all the bending they go through with every step. But Shoe Goo proved me wrong. The most impressive repairs were the re-attaching of fully separated soles for a pair of tennis shoes and for the Teva sandals. After extensive use, the soles of both pair of shoes are still attached like they were repaired yesterday. What Worked For Me - Tips For Best Results 1. Use adequate ventilation. - This glue emits very strong solvent vapors, so use with adequate ventilation. Open the windows, work in the garage or on the patio, whatever is necessary. Keep in mind that strong vapors will continue to be emitted for days as the glue sets. You really do not want to breathe this solvent any longer than necessary. 2. Make sure the bonding surfaces are clean. - The separated soles on my shoes were dirty on both sides, so I first washed them with soap and water and after drying went over them again with alcohol. If the soles still had pliable glue on them, I would have used acetone (fingernail polish remover) to try and remove it. I believe the directions also mention that acetone can be used to remove excess Shoe Goo and for after-repair cleanup. 3. Use tape for masking. - I used paper tape to mask areas where I did not want the glue to go - like on either side of the seam where the sole attaches. And once the soles were attached, I put weight on the shoe so any excess glue would squeeze out. The excess glue was removed and then the tape was removed immediately so it didn't get stuck and become part of the shoe. 4. Work quickly. - Once the product is dispensed from the tube it starts to skim over and to dry out immediately. Plan ahead. Know where and how much glue needs to be squeezed out. Use something like a putty knife to quickly spread the glue so it covers the entire face of the parts to be glued. Wear some disposable gloves in case you need to move glue around into nooks and crannies with your fingers before attaching the sole. I also used 'parts' brushes to help move glue into the nooks and crannies. (Parts brushes are small brushes with somewhat stiff and coarse bristles, meant for non-painting applications. Typically sold in packs, they can usually be found in the hardware aisles of your local hardware store.) 5. Keep the glued parts in close contact while drying. - While drying, I made sure the parts stayed in close contact by placing a heavy weight on the shoe. I also needed to use heavy duty (Gorilla) tape to flatten out decorative edges on the Teva sandals. 6. Allow time for the glue to Set. - From memory, I believe the directions say that when re-attaching soles, allow them to sit for 24 hours, then put them on and put your full weight on the shoes to remove air pockets, and that it may take up to 72 hours for the glue to fully set. I followed those directions but allowed additional time for the glue to fully cure. The glue 'sets' through the evaporation of the solvent from the glue. But if the glue is trapped between two non-porous surfaces, the solvent will not evaporate quickly. So, I let the glue cure until I could just barely smell the strong solvent when the repaired soles were held next to my nose. And that took about a week for the Tevas and also for one pair of tennis shoes. Waiting that long may very well not be necessary, but I had the time to be sure the glue was dry. Notes: Once fully cured, this glue is TOUGH. I used a metal putty knife to spread it onto the shoe soles, and once dry it was very difficult to remove from the knife - even with a new box cutter blade. (I didn't try acetone.) The cured glue is also stretchy, in a heavy duty kind of way. It seems to be the perfect product for use on shoes, even those that bend a lot like tennis shoes and Teva sandals. And if your project requires spreading the glue, I recommend using something disposable like plastic putty knives from the dollar store. Or popsicle sticks. It appears that Shoe Goo will adhere to almost any surface, so you'll probably find a use for any remaining product. One of my old, comfortable slippers were about to wear through on one side so I slathered a layer of Shoe Goo over the weak area and it was fixed. The too-thin leather heel on another old, comfortable slipper was in torn tatters so I Shoe-Goo'd a cloth patch over the problem area and it's back in service. Neither of these two repairs is particularly attractive but since they're house shoes - function and comfort are more important than style. Be sure to screw the cap back on tightly after each use. And if you anticipate leaving the remaining product on the shelf for more than a day or two, you might consider applying a bead of petroleum jelly, grease or something similar under the rim of the attached cap to help prevent the remaining product from drying out. I would recommend Shoe Goo to anyone who wants to repair shoes at home. ==================================== Follow-Up, 12-2-2023 The following repairs were made at the same time as the repairs to my other shoes, described above. And all of these repairs are still holding well. ---------- Detail of the repairs made to my Sketcher Sport tennis shoes that look like a cross between tennis shoes and hiking boots. The heavy leather upper on one shoe sheared off cleanly where it connected to the shoe bed at the arch. It looked as if a very sharp knife was used to cut the leather right next to the bed. To align the leather before gluing, tape was applied to the edge of the sole, and then across the upper leather. Then, a bead of Shoe Goo was applied INSIDE the shoe. When that dried, and with the leather upper now secured in the proper position, the tape was removed and glue was applied along the new seam on the outside of the shoe. Since I was gluing the edge of the leather upper directly to the shoe bed (abutting at a 90 degree angle) I had strong doubts about this particular repair. However, it's still holding today. Kind of crazy! Also, the rubber toe protectors on the very front of both shoes had become detached and curled. To properly secure those pieces, they had to be glued in three steps, using strong tape to secure them into position. The result was ugly but a permanent black marker made the repairs nearly invisible, disappearing into the surrounding black material. About the Sketchers: I've had them for several years, but they've been gently and only occasionally used. I'm very disappointed these Sketcher shoes self-deteriorated the way they did with only light use. It points to substandard materials and poor construction. I doubt I'll ever buy another pair of Sketchers. Breakdown of my Follow-Up: 1. Shoe Goo is an amazing product! 2. If you're thinking about buying Sketcher shoes, I suggest you take another look at other brands. 3. If you do buy Sketcher shoes, try to remember how well Shoe Goo works! Read more

This adhesive worked perfectly for repairing the loose soles on two different pairs of boots. Application was simple, the glue spread easily, and it dried clear just as advertised. After letting it cure, both pairs feel solid again with no lifting or separation. I’ve worn the boots multiple times since the repair, including regular daily use, and there have been zero issues. It saved me from having to replace perfectly good boots. If you have worn or separating soles, this is an easy, affordable fix that actually holds. Highly recommended. Read more

Shoe goo does the job, but unless you need to do a lot of shoes at once, it isn’t very economical. If they do not sell it in single use tubes, they should. I used mine to repair one pair of shoes. It did a great job. The glue is strong, it holds the pesky insoles into the shoes (finally!), and it didn’t leave lumpy lines I could feel through the insoles. However, when I went back several weeks later to repair a sole that had come loose on a pair of boots, the cap had permanently bonded itself to the nozzle, rendering 90% of the tube useless. I always clean the nozzle before I put the cap back on, so I am not sure how that happened. It works. It really does. You just have to use it all at once. Read more

I repaired my son's shoes with this about six months ago. The sole had come off from where he kicks them off his feet. They were expensive shoes, so I decided to repair them instead of replacing them. To my surprise, the glue is still holding everything together! Great product. Read more

Repairs Like a Pro—Saves Old Shoes, Boots, and More I’ve used SOF SOLE Shoe Goo several times now, and it’s one of those rare repair products that really lives up to its name. The consistency is thick and tacky, which helps it stay exactly where you apply it. It spreads easily with a toothpick or small stick and dries clear overnight. Once cured, the bond feels almost rubberized—flexible yet tough. I first used it to reattach the sole of a pair of leather boots that had started to peel at the toe. After letting them sit for a full day, the repair looked clean and held perfectly through wet pavement and daily wear. Since then, I’ve used the same tube for small patch jobs—like reinforcing sandal straps, fixing sneaker soles, and even sealing a worn heel on a pair of loafers. It’s surprisingly versatile and a great “emergency fix” for any kind of footwear. A few tips: use it in a well-ventilated area, wear disposable gloves, and resist the temptation to wear the shoes too soon—it really needs the full 24-hour cure to reach full strength. The 3.7 oz tube goes a long way, enough for several repairs. Bottom line: a dependable, long-lasting adhesive that can genuinely extend the life of your shoes, boots, and gear. A must-have for anyone who hates throwing away comfortable favorites over minor damage. Read more

I wear out my shoes on the back left heel and I had some boots that were expensive but had no separate heel so it would have been costly to resolve the whole bout. I used this with rubber heel plates to reinforce the worn area. I was very careful to clean, sand, and allow several days for curing before I wore the boots. I think the glue has outlasted the heel plate , the performance of this glue is excellent! Read more