YoLink SpeakerHub Two Motion Sensor Smart Home and Security Kit Audio Hub Plays Tones Sounds Spoken Messages LoRa-Powered

This is a great security alert system for the money. Works as advertised and super easy to set up. I love that is sends immediate notifications. I already have security video cameras that I can access on my phone so when I'm away from home and get alerts from YoLink, I know to check my cameras. Highly recommend! I also love that if you have multiple sensors, the system will tell you which sensor has been tripped. Read more

I am using the YoLink Speaker Hub and two Motion Sensors around my house. This system uses LoRa and has fantastic range. They have been very dependable from the very start. The motion sensors are extremely sensitive and will alert when motion is detected even if it detects a small creature like a squirrel. There are one or two things, so far, I wish were a little better. One, the lowest setting is still very sensitive. I would like even a lower setting. And although the system is extremely easy to set up, I find it difficult to set up a “disable” button to turn the system off while working around the house. These are not the fault of the equipment, so I am giving 5 stars. Overall, I am very happy with YoLink. Read more

I've used a few different versions of driveway sensors and these are by far the best. With the audio enabled base station I can set up my own notification sound for when the alarm is triggered. This is incredibly handy for me because I can switch it up when one of the dogs learns what the sound is and barks like crazy when it goes off. Setup is really easy within the app and there is Alexa and IFTTT integration if needed. I've had no issues with connectivity or range so far and that is with the base station in the basement if a brick home and the sensor 100 yards away outside. I don't get any false notifications on the medium setting and so far it hasnt missed any so it seem quite accurate. Read more

Pairs nicely with home assistant, and the range of LoRa is helpful for more remote setups. Sensor triggers reliably. Read more

Seriously impressed. I’ve tried multiple motion sensors online setups before and I was disappointed with each one until finding the YoLink one. The sensors work the way they should, the notifications are instant, the settings and tweaks you can do are impressive. Linking the base to my wifi and connecting multiple sensors was not only easy, it’s exactly how I would design the QR code, menus, and devices naming. I’m going to be looking through yolinks inventory now because I’m so impressed. Read more

UPDATE: A few weeks later the company issued a total recall of these damaged sensors sending free replacement to everybody who purchased them (allowing the customers to keep the damaged sensors). This is a sign of a company that cares about quality and customers. The damaged units are fully functional, just not weatherproof anymore, so you could use them inside. As you can see in photos the screws on the back were over-torqued to a degree, where the rubber seal was completely compressed and then the plastic back cracked. Only one of eight sensors had been properly assembled. One had only a single corner cracked, so I applied a bit of glue hoping it will seal the crack and kept those two. If you do buy make sure to check. Read more

We are on a large property with young kids and have been through a ton of solutions. I wish I would have found YoLink sooner as it has been simple to set up and works amazing. We have had it up for 4 months or so, so we have had some testing time too. Read more

I was really excited to see this new sensor product being offered. I am familiar with LoRa as I was trying to build my own road sensor because I was frustrated with commercial road sensor offerings. The available road sensors were either inconsistent, or they worked well but only lasted about a year before developing problems. I built a transmitter and receiver from a small microprocessor (Adafruit Feather 32u) and wandered the length of my property (~36 acres) and the LoRa connected to the house receiver and also got back a reply from the house receiver everywhere I went. This included connectivity through trees and non-line-of-sight behind hills! So I had high hopes for this Yolink product. In addition, they offer other sensors like temperature, water leaks, the ability to activate relays or outlets by sensors, etc. As you may have guessed, I've done a fair amount of program coding, building websites, setting up my multiple network devices on the farm, etc. But it took me a long time to even get the speaker hub device connected after downloading and installing their app. The main problem turned out to be that I didn't want to give Yolink my location. Their software won't connect without knowing where you are! And even after allowing it to know my location, it wouldn't connect without knowing my "precise" or exact location. Talk about a lack of privacy! But I sucked it up and gave in. After getting the hub set up, adding the two sensors was pretty simple. Programming them, not so much. I'm still confused about the settings. I've downloaded and read through their manuals, etc. for both the hub and the outdoor motion sensors. The sensors, or maybe the software, just does bizarre things. My setup had the hub on a desk in the front of the house next to windows that face both directions up and down the road to the sensors. After moving my hand in front of each sensor to make sure they were working, I placed the sensors fairly close to the house, about 500 feet away. They are pretty close to a direct line of sight in each direction but through a few branches from trees and some brush. Both sensors showed online and working through the app. Unfortunately, neither detected a car passing a while later. I also walked down to one, waved my arms in front of it, saw the LED light, yet it never activated the hub. Someone was inside and didn't hear it, and the history tab didn't show it. So I thought I must have screwed up the settings. I have it set to "always" alarm. Sensitivity set to "high". I'm only guessing at what this one does: "Time to enter No-Motion state". I originally thought it was a time-out to quit functioning after sensing for a while. I now believe it is the time after the sensor no longer senses motion, before it resets, and will again sense motion. For instance, if I set it to the minimum of one minute and a person walks by, the sensor will alarm. If another person walks by in less than a minute it will NOT alarm. Then (and I'm still unsure) it may start another minute of timeout because it sensed the second person, and so on. So if you have 100 people walking by the sensor every 50 seconds, it will never alarm until they have all passed and the one-minute time-out is complete. In this example, it would be about 84 minutes later it would start working again after all 100 people passed. I had this setting at "disabled". I have no clue whether this means it will alarm without a timeout, or it will never alarm again, because there is no timeout. I also set it to one minute. Trying to test it proved inconclusive. Looking at the history for one sensor, I saw it detected motion at about 4PM. The next entry was "no motion detected". I figured that must be the timeout, and several times it was about one minute which was where the timeout was set. Other times it was THE NEXT DAY, nearly 20 hours later. The sensor is facing a hillside. There is nothing to move except a few leaves, so why would it take a day to stop sensing motion? In addition, some settings randomly reverted to earlier default settings without any intervention by me. I would re-start the app, open the motion sensor page, and the "Time to enter No-Motion state" would be back to "Not detected over 5 mintes" or "Disabled"?????? Then there is "Alert Hold". Again, didn't get enough explanation to know what this is supposed to do. You can set it at zero or longer in minutes and hours. Is this only for an added device, such as an outlet that might turn on a light and the "Alert Hold" is for how long it is turned on? If you have no other devices and set it to zero, does the alert still work? Not enough hours in the day to try to test that. Both sensors have just randomly shown they were "offline". What is that supposed to mean? They can't be reached by the hub? They are tired and need a rest? They are too far away and lose connectivity randomly, sometimes connected, sometimes not? Are they doing some kind of internal programming and have to disconnect while doing it? Possibly any of those ... or none of those. But even when showing "online", good battery, and showing the temperature they still didn't detect movement of either cars or humans from less than 15 feet away and set on "high". That is their primary job, right? Does the app need to be constantly running for them to work correctly? Perhaps a note when you fire up the app saying "Hey, I tried to do a heartbeat with SensorOne and it did not respond. The last signal intensity was marginal. Is it too far away?". Or: "The last signal intensity was good. Did you move it or the hub? If not, your sensor may be defective". Slapping down a black box and having an expectation of how it is "supposed" to operate is not very helpful. Before receiving these, I also asked the seller if these would function without being connected to the internet. The answer was "For full functionality, our devices need to connect with one of our hubs, and that hub needs to be on the internet with a connection to our cloud server." That didn't answer the question so I then asked just "what functionality would be available without an internet connection"? That question was ignored. Go figure. I had hoped I could at least use these as "dumb" sensors after setup, and without being connected to the internet. You know, a simple alert when there is movement without all the history, or temperatures, or added scenes, etc. The odd functionality of these devices or their software, the limited sensitivity, and the partial documentation, etc., first made me frustrated, and now just makes me sad. I received these as a present, but all of the other road sensors I have bought in the past have worked much, much better than these, and most of them even after months outside in the Oregon rainy winters. Also, every other sensor I have bought has functioned at the same distance at which I set these, at least initially. Perhaps they are excellent within short ranges as is typical in a town yard. That is too limited for my needs. It is possible I received a defective device or devices. Even so, I'm not sure I can take all the time needed to set up new ones. And, if they are not tested before shipping, I don't really want to be their unpaid quality control. Bottom line is that I am VERY disappointed. I do know the LoRa technology can do better (numerous people have tested LoRa over miles, even a hundred miles line of sight, and they even connected to a satellite in orbit with LoRa). I'm guessing I need to keep working on my homemade sensor or wait for a decent commercial version that is designed for a rural user such as myself. Read more