ANCEL BM1000 Bluetooth Battery Monitor with 400A Shunt Wide 10-120V Range Smart Battery Meter Real-Time Voltage Current SOC

2 minute install. Great software. Tells you everything you need to monitor your car's battery and charging system. Bought one for each car... software allows for multi vehicle monitoring. Only wish they had a wifi model... Read more

It works even in the four pack of large 1150amp batteries I have in my truck and seems super reliable. The app for it has a lot of useful functions and is super easy to configure and understand. No pairing is required. The app sees the monitor automatically and just works. I literally had it installed and up and running in two minutes. Device itself is about the size of a pack of playing cards and Bluetooth range on it is good. If you’ve got a vehicle like mine where the gauge shows the charging rate instead of the state of the batteries charge this is a very useful device and the readings it gives where within .01% of what my Fluke multimeter says so accuracy is very good. Read more

I bought 2 of these. They are easy to set up with Bluetooth and works about 30 feet away. They give valuable information with respect to battery performance and even record in a nice graph to be retrieved later for examination in Excel charts. They can show State of Charge, Voltage and Temperature. That in itself is good enough for most users, but it can also evaluate starting and cranking performance. The problem comes with location-labeling and trip information. (See photo below). My cars are a RAV4 and a 08 Fit. When locating these cars using the App, the labels on the cars are reversed displaying the Honda where the RAV is and vice versa. This also occurs when using the GPS on trips. Another problem is displaying the trips. Sometimes mileage is shown, sometimes not. (See photo). Distances from the cars is also wrong. Photo shows distance as over 600 feet, when in reality, is 45 feet between the two vehicles. The battery display is about .3 volts higher than actual. If these errors were fixed I'd give it 5 stars... it is still a good device for battery health if that is what you need. Read more

I wasn't looking for this monitor when I happened upon it on Amazon. I work in the motorsports industry and had not seen anything like this in the dealerships and shops I visit on a regular basis. And since I'm an electronics geek who's also in the motorsports field I had to try this. Before I ordered however I checked out the Ancel Battery Monitor App in the iOS store. There were only 4 ratings at the time with three 5-star ratings and one 1-star rating, the app looked promising so I ignored the one negative rating and ordered up. Once in hand I found the ANCEL BM300 Battery Tester/Monitor unit to be smaller than expected, measuring 3 ¾" Wide x 2" Long and 7/8" Thick. (Tapered design, see the pic below with measurements). The two lead wires are roughly 7" long with open clips on the end. To install I just had to hook up the leads to the positive and negative ends of the battery on my motorcycle. I then went into the app and expected to have to fool around with Bluetooth connections but the monitor had already paired to my phone and was showing the current battery voltage. Sweet! (see pic) From that point I started the motorcycle and the ANCEL BM300 showed the current charging rate and battery voltage with the battery voltage showing on a line graph. (see pic) I then ran the Charging Test and the charging voltage at idle and high RPM was shown. (see pic) The ANCEL BM300 will also perform a Cranking Test which shows the cranking voltage as a numeral and also on a line graph. Note: I like that the app shows good readings in Green and low or bad readings in Red. The Ancel also has a Trip setting which gives you a history showing times and duration for the vehicle (car, motorcycle, etc.) has been running. The app also has some more features in the System Set-Up allowing set two separate Power alarms at a % of your choice. These alarms will remind you once the battery is below the chosen percentages, I have mine set up at 70% and 50%. You can also choose to have a Daily Power Notification or Abnormal Cranking Notification. So far I am very impressed with the functionality and ease of use of the ANCEL BM300. The Bluetooth range is strong enough that I can check the battery status on my motorcycle from my living room with it being 30 feet away inside a garage with concrete block walls. The only negative I can think of is that as far as I can tell the Ancel Battery Monitor App can only work with one monitor at a time. If it worked with more than one vehicle I would buy one for my truck and my camper as well. I would also have an extra monitor to use for diagnosing battery/charging issues on the motorcycles and off-road vehicles I encounter for work. Read more

This is a great product. It does exactly what it says it will do. Packed with enough features for you to monitor your battery’s performance or lack of. The app is very user friendly, once you take the time to explore, you’ll realize how much information is at your fingertips. Even when you’re out of bluetooth range, the information is still being stored and waiting. I think I was able to go as far back as five days and view my battery’s performance data. Customer service is excellent. If you ever have any issues, they will go to the extreme to help you. Believe me. Now the Bluetooth signal maybe an issue for some but don’t ask for more than many other devices cannot offer either. Plus understand that the module is inside your engine bay (in most cases). Just get it. I would like to thank my Ford F150 Powerboost members who introduced me to this nifty piece of equipment. Because of how my truck’s hood comes down very close to my main battery, I have to keep it on the side. Read more

Works great so far ( 1 week). Easy to install and set up. Read more

My mechanic recommended this device for my Chevy Bolt EV and I love it. Lucky I did not pay much attention to the reviews about Bluetooth disconnect issues. I had no problems thus far. Read more