Mount-It Monitor Wall Mount Arm Full-Motion Gas Spring Fits 13 32 Screens up to 14 3 lbs VESA

I’ve been using this mount for close to 6 months now with a 32” monitor and it’s been flawless. Very sturdy, the monitor never moves or sags. Ordering a second one now for a dual setup. Read more

Was pretty easy to mount, though I was a little paranoid about making sure it was positioned right before I started drilling starter holes. I was using my iphone prior to this, but now I can see the drum notation scores much better with my 70 year old eyes! Nice looking mount... Read more

Worked great for a 14 lb monitor Read more

This wall mount offered the best articulation for my needs. The high point is the screen tilt range. Most other wall mounts only do 5° forward and 15° back. Since I'm not using it for work/desk needs and instead in my room for movies and gaming, the tilt range on this one is amazing. The frame itself is sturdy material and of sound construction. The articulation joints are easy to adjust and manipulate. There are just a couple down sides: •I'm not a huge fan of the angle of the sections at the elbow joint but the screen tilt more than compensates for that. •My thin, curved, borderless 24" monitor (Scepter) isn't actually heavy enough to activate the elbow articulation piston, which is really hard to manipulate by hand when the arm isn't yet connected to the wall. There isn't a way to adjust the pressure of the piston, unfortunately. Once I had the thing mounted and attached the monitor, I had to add a 3lb weight to the end of the arm to get the piston articulation to function as intended. Otherwise, I'm pretty content with my purchase. This is the 2nd one I bought after sending a different kind/brand back. Read more

I got a couple of these for my two monitors. I have a bad experience with double wall mounts, so I wanted two separate single mounts. Pros -- It works as described, it's easy enough to set-up, and it's easy to adjust the tension etc. Cons -- Due to the stud spacing in my wall and the way the arms work, I have to set my monitors at a certain height to get them to line up flush like I want and I have to turn them slightly more inwards than I want. I think this product is great overall, but it'd be ideal if it had ONE more joint on it to allow a little more flexible left-right movement. I tried to measure out where I should place them, but the stud locations limited my options, and even within their range, there was no good way to test them other than putting them up and hoping it all lines up in the way you want. Again, an extra joint to add a bit more range of motion would be ideal. Read more

I purchased 3 of these and mounted 3 27" monitors on them. Pros: Easy to install - included hardware is great. Installed them directly into studs and they are very solid and look good. Cable management built in was easy to use and does a good job holding cables out of the way. Adjusting the monitors is pretty easy. Adjusting tension is easy to do as well. Cons: The monitors can't sit directly in front of the wall mount due to the different lengths of the 2 arms. This really wasn't a big deal for me but was a slight nuisance as I did want the center monitor directly in front of the stud that this was mounted on. This was not significant enough for me to not rate this 5 stars overall. Overall: Great mount, easy to install, definitely would recommend. Read more

I bought two singles rather than one double for my dual monitor set up in my home office. I found this provided greater range of motion side to side. I am short so I use them for a stand sit desk. They are very sturdy and easy to move up and down. I don't know what I would do without them because I have severe neck issues and I sit/stand every hour. I have now had them for one year and they are like brand new. When you go to install make sure that you sit down or stand to get the middle of the screen exactly where it is comfortable for you. If someone is taller than 5'4", I don't the range of motion will be suitable. Read more

My review is more of a question. Every picture from the installation guide to the box to the marketing shows the X mount that attaches the arm to the tv actually looks like an X up and down left to right as you see it typed. Why do mine (I bought 2 at one time) seem to be crooked (see pictures attached) this is making it difficult for my brain to understand how I can successfully mount my TV onto the arm properly. As the X does not seem to be able to rotate so no matter which way I rotate or move the arm the X still remains crooked. This seemed so simple so where have I gone wrong? Read more